Post by petebert on Jul 7, 2010 0:23:41 GMT
Hi, I just started using the DC-9 and Hilmerby panel. So far I've only found two types of checklists and I've read over the tutorial here. Theres the Northwest one that doesnt list all the steps the tutorial lists for the engine start and theres no APU section. Theres a few on the internet that seem to have a few hundred steps, a lot of which are not available on the panel. The checklist on the Hilmerby website is one these.
So I decided to make one for myself, its mainly a combo of this forums tutorial and the NWA checklist. I'll post below what I've done so far, right now its a rough edit. I did a trial run and the APU and engines started right up.
Anyone know if there is a checklist like this out there already? I dont want to waste my time if there is one available. It does look better then this but the cut & paste to a forum butchers it a little.
APU START
Start Pump..............................................ON
Battery Switch........................................ON
APU Gen..................................Reset & ON
APU Air.................................................OFF
APU L & R Bus....................................OFF
APU Master...................................Start/Run
APU Air..................................................ON
APU PWR AVAIL..................................ckd
APU Gen...........................................NORM
APU L & R Bus......................................ON
Start Pump.............................................OFF
DC Bus Volt..........................................APU
BEFORE START
Fuel.......................................................OFF
Yaw Damper...........................................ON
Anti-Skid...............................................OFF
AC & DC Bus X Ties........AUTO & OPEN
Emer Pwr...............................................OFF
Air Cond Auto Shutoff.........................ARM
Pitot Heat.............................................CAPT
Windshield Heat.....................................ON
Hyd Pumps..............................................HI
Altimeter................................................ckd
Fuel......................................................loaded
Fuel X-Feed..........................................OFF
PUSHBACK/START
A/C Supply............................................OFF
Ram Air.................................................OFF
Seat Belt Sign.........................................ON
Fuel Tanks..............................................ON
Start Pump..............................................ON
Ignition........................................Full Down
Anti-Collision Lights.............................ON
Engine Ice Protect......................as required
Pneu X Feed Valves.............................Open
#2 Eng Start...........................................ON
N2 at 20% #2 Fuel.................................ON
repeat for #1
Ignition..................................................OFF
Start Pump.............................................OFF
APU Master...........................................OFF
APU Air.................................................OFF
APU Pwr Light Exstinguished...............ckd
L & R Gen...............................................ON
DC Bus Volt...........................Batt Amp/Volt
APU Gen............................................Reset
APU L & R Bus..................................OFF
Galley....................................................ON
So I decided to make one for myself, its mainly a combo of this forums tutorial and the NWA checklist. I'll post below what I've done so far, right now its a rough edit. I did a trial run and the APU and engines started right up.
Anyone know if there is a checklist like this out there already? I dont want to waste my time if there is one available. It does look better then this but the cut & paste to a forum butchers it a little.
APU START
Start Pump..............................................ON
Battery Switch........................................ON
APU Gen..................................Reset & ON
APU Air.................................................OFF
APU L & R Bus....................................OFF
APU Master...................................Start/Run
APU Air..................................................ON
APU PWR AVAIL..................................ckd
APU Gen...........................................NORM
APU L & R Bus......................................ON
Start Pump.............................................OFF
DC Bus Volt..........................................APU
BEFORE START
Fuel.......................................................OFF
Yaw Damper...........................................ON
Anti-Skid...............................................OFF
AC & DC Bus X Ties........AUTO & OPEN
Emer Pwr...............................................OFF
Air Cond Auto Shutoff.........................ARM
Pitot Heat.............................................CAPT
Windshield Heat.....................................ON
Hyd Pumps..............................................HI
Altimeter................................................ckd
Fuel......................................................loaded
Fuel X-Feed..........................................OFF
PUSHBACK/START
A/C Supply............................................OFF
Ram Air.................................................OFF
Seat Belt Sign.........................................ON
Fuel Tanks..............................................ON
Start Pump..............................................ON
Ignition........................................Full Down
Anti-Collision Lights.............................ON
Engine Ice Protect......................as required
Pneu X Feed Valves.............................Open
#2 Eng Start...........................................ON
N2 at 20% #2 Fuel.................................ON
repeat for #1
Ignition..................................................OFF
Start Pump.............................................OFF
APU Master...........................................OFF
APU Air.................................................OFF
APU Pwr Light Exstinguished...............ckd
L & R Gen...............................................ON
DC Bus Volt...........................Batt Amp/Volt
APU Gen............................................Reset
APU L & R Bus..................................OFF
Galley....................................................ON